- Journey Builder Wait
- want to use method name instead of object name in vf page
- Approval process optimization
- Dashboards using Lightning Component
- Insert Account Record by REST API and Postman
- what is the daily limit of time based workflow email alert?
- Send email using email templates in Scheduler apex
- Move “actions” dropdown in Lightning:datatable in front of other page elements
- Invalid Type Triggered Send Definition
- Customization of lightning components in Managed Package
- pdf generation with arabic content -not display arabic content
- How to Rename standard field label 'Contact Name' on Case Object
- Return on investment of cryptocurrency
- job permissibility
- Raspberry pi shutdown when running python code
- Broken SD Card Cannot Open
- How to regain internet connection on raspberry pi using ENC28J60?
- How can I change the RAM split?
- I want to learn . Exe - can you recommend best place in chennai, india
- Why does the size of hybrid orbitals vary as sp³>sp²>sp?
Can't program Arduino via Bluetooth (HC-06) with a Mac
I bought a HC-06 Module for my Arduino Uno the other day, yesterday it arrived and I'm having trouble using it with the Arduino IDE.
I set it up, connecting 5V, GND and RX/TX crossed. After a bit of searching, it shows up on the bluetooth settings on the macbook. When I click "connect", it fails, after I click "Options", then set the Pin to 1234 it says "Connected". The LED on the HC-06 is still blinking (which is OK I guess, since I'm not yet communicating).
I have a Sketch running on the Uno that prints out some text. When I open the serial monitor (after connecting like above) it works, displaying the values I expect. However, after closing the serial monitor the HC-06 changes to "not connected" on the mac.
Also, if I try to upload code via the Arduino IDE it states: avrdude: ser_open(): can't open device "/dev/tty.HC-06-DevB": Resource busy
ioctl("TIOCMGET"): Inappropriate ioctl for device or throws a processing.app.SerialException: Fehler beim Öffnen des seriellen
The on-board USB-to-serial pulses the reset line to start the bootloader. HC-0x don't have the extra signal available that USB uses for that so you'll have to manually reset the Arduino just as - or very slightly after - you click to start the upload on your Mac; you may need to experiment to get the timing right, but once you know it, it isn't hard to do. Keep Rx & Tx crossed as you do for Bluetooth terminal communication. And even with all that, I've never achieved anything like USB upload speeds (baud rate for baud rate) using Bluetooth.
In brief, it could be timing, baud-rate, or pairing.
I find it easy to get the timing: hold reset / click (and let go) the upload button / release reset. It doesn't need to be so fast that it's a challenge to coordinate but do it faster than counting seconds.
Your HC-06's baud rate will have to match the baud-rate your boot-loader expects. It looks like Uno's bootloader's use 19200 baud (and there are some way older ones that used 9600)2018-01-13 01:17:05
Regarding the ability to upload, that is correct - you won't be able to upload code via Bluetooth. In addition to providing a serial connection, the USB connection does something extra (hold reset, I think), when you upload via serial-over-usb.2018-01-13 01:26:03
If I remember correctly, you do not want to cross TX and RX.
Usually, you cross TX/RX because you are looking at it from the opposite side - the PC's TX is the Arduino's RX and vice-versa.
However, in the case of BlueTooth, the HC-06 has the same perspective as the Arduino - TX (transmit) is TX on the HC-06, since that is what the HC-06 transmits (over Bluetooth).
Also, if you are connect your Arduino via USB, the TX & RX are also connected via USB; I don't know if this would cause cross-talk. It shouldn't (so long as you don't send to your Arduino using Bluetooth AND USB at the same time), but it may. Also, as you're programming the Arduino using Bluetooth, you may get the Arduino's responses coming back to you via Bluetooth.
Go read http://arduino.cc/en/Hacking/Bootloader?from=Tutorial.Bootloader - this is all about the bootloader.
It seems from that that current bootloaders run at 19200, some older ones run at 9600. There are commands to program the speed on HC-02018-01-13 01:54:23
After dealing with the problem for several hours I unexpectedly solve the problem.
The HC-06's LED keep blinking after I entered the "1234" code. In my case (I'm using Windows 10), the HC-06 status changed to "connected" for few seconds and then changed to "Paired". Once I opened the correct COM port to receive data from the HC-06 to my PC computer, the LED changed to solid ON. Then I was able to catch data from my Arduino UNO. As soon as I closed the COM port in my PC (I used CoolTerm), the LED changed to blinking back again. The COM port I used to receive the data was the one indicated with direction "Outgoing" in the PC's Bluetooth settings. So, I was expecting the HC-06 to behave as my Bluetooth speakers or my Bluetooth headphones: Always connected. I was wrong and it cost me several hours of testing.
In my firsts tests I focused opening the COM port with direction "Incoming". Nothing happened here and I lost a lot of time. I tested my wiring between the arduino and the HT-06 m2018-01-13 02:11:26
not enough rep to vote up Roldofo's comment, but his suggestion to rename to "ArduinoBT01" seem to make all the difference!2018-01-13 02:37:00